Yinstar 12-Inch DTF Printer, 2024: Why Dual XP600 Not i3200, Anti-Collision Sensors, Wide Pinch Rollers, Pause-to-Clean

Published 11 February 2024

Twelve-inch Yinstar, dual XP600, fully automatic roll to roll, filmed on our floor in February 2024. I went through what makes it worth more than the generic Chinese 12-inch: sensors that stop the head, rollers that feed straight, a pause button that lets you clean mid-roll, and a shaker with four heating coils. And the two things I always say: do not put i3200 heads on a 12-inch, and do not leave any DTF printer running without an operator.

Walkthrough, 7 min 21 s. February 2024. · Watch on YouTube

What the video shows

  1. 0:01 — 12-inch Yinstar: dual XP600; i3200 only makes sense at 24 inch
  2. 0:41 — Heater plate under the print area; margin ruler
  3. 1:03 — Anti-collision sensors on both ends of the head
  4. 1:51 — Wide pinch rollers with precise lever adjustment
  5. 2:26 — Adjustable display
  6. 2:40 — Pause a roll job, clean the head, resume
  7. 3:08 — 1.5 kg ink tanks; circulation; filter and suction
  8. 3:33 — Powder shaker: four heating coils, control panel
  9. 4:40 — One 12-inch roll is about 220 A3 sheets
  10. 5:18 — Build quality; eco-solvent-grade motors; emergency switch
  11. 5:35 — Always one operator with the machine
  12. 5:52 — Service: fill inks, solution in the capping; technician install; video calls

XP600, not i3200, at 12 inch

Dual XP600 is the right head for a 12-inch machine. i3200 is offered, and I do not recommend it at this width: the head costs more, the speed advantage does not show on a 12-inch roll, and a head strike is twice as expensive. At 24 inch, i3200 makes sense. The comparison is in XP600 vs i3200.

Card: features of the Yinstar 12-inch dual XP600 DTF printer from the 2024 walkthrough
Why it costs more than the generic 12-inch.
Yinstar 12-inch dual head DTF printer printing from a roll, caption master of DTF 12 inch dual head printer
The 12-inch Yinstar on the floor.

Sensors and rollers

The head bump sensors sit on both ends of the carriage. If film lifts and touches a sensor, the machine pauses before the head reaches it; most brands give you this on 24-inch only. The pinch rollers are wide and adjusted with a precise lever, so feeding stays straight; on generic models it is a handle that lifts the rollers with no control. A preheat plate sits just below the print area and the display tilts to where you stand.

Print head carriage of the Yinstar 12-inch over the film, caption preheat plate just below the print area
Preheat plate below the print area; sensors at both ends of the carriage.
Front of the Yinstar 12-inch showing the pinch roller assembly and control panel
Wide pinch rollers with lever adjustment.

Pause to clean

Printing a roll and the head needs a clean? Press pause, press the right arrow, clean, resume. The job is not deleted and the film does not move. That one feature saves a roll a week.

Yinstar 12-inch printer paused with the head over the film during a roll job
Paused mid-roll; clean, then resume.

Ink, shaker, output

Tanks hold about 1.5 kg of ink each, with circulation, a filter and a suction motor. The powder shaker is fully automatic with four heating coils and its own control panel; print goes in one end and a cured transfer comes out the other. One 12-inch roll gives roughly 220 A3-equivalent sheets. Motors are the kind used on eco-solvent printers, parts are available, and there is an emergency stop.

Inside the Yinstar powder shaker showing the four heating coils glowing
Four heating coils inside the shaker.
Yinstar 12-inch DTF printer with printed white-ink transfers coming out onto the table
Transfers coming off the roll.

Operator and service

It is automatic, and you still need one operator on it the whole time it runs. No DTF printer is leave-and-go. Maintenance is filling inks and keeping solution in the capping unit; our technician installs and shows you, every fault has its own video on the channel, and most issues are solved on a video call. The printer is here; the 24-inch i3200 is here.

Frequently asked questions

XP600 or i3200 on a 12-inch DTF printer?

XP600. i3200 costs more, shows no real speed gain at 12 inch, and doubles the cost of a head strike. Use i3200 at 24 inch.

What do anti-collision sensors do?

Pause the machine when lifted film touches the sensor, before the head is hit. Fitted at both ends on this model.

Can I clean the head mid-roll?

Yes. Pause, right arrow, clean, resume. The job stays.

How much does one roll print?

About 220 A3-equivalent sheets per 12-inch roll.

Does it need an operator?

Yes, always, while it runs.

Related guides

Looking at 12-inch machines?

WhatsApp your daily sheet count. If a 12-inch is right, the demo is at the Navi Mumbai or Hyderabad unit.

WhatsApp +91 86555 56060

More videos: Dedicated DTF printers (X-ARC, Yinstar)