L1800 or a 12-Inch XP600 Dual Head? What Each Is Good For, Filmed at Print Innovation Tiruppur

Published 6 April 2023

Two printers on the stall at Print Innovation in Tiruppur: a 12-inch XP600 dual head with its powder shaker, and our L1800-based DTF printer with every module fitted. The question from every visitor was the same, which one, so I answered it on camera: it depends on your sheets per day, and on whether you want to stand next to the machine all day. Seven minutes, with the oven-versus-shaker argument that still gets me into trouble.

Expo walkthrough, 7 min 10 s. Tiruppur, 2023. · Watch on YouTube

What the video shows

  1. 0:01 — Print Innovation Tiruppur: 12-inch XP600 dual head with shaker
  2. 0:19 — 100 to 200 sheets a day: go dual head; lower head cost than 24 inch
  3. 1:02 — DTF oven; the L1800-based printer with forward-reverse
  4. 1:31 — PE simulator module; ink circulation for white density
  5. 2:12 — About 1 to 1.5 rolls a day on the L1800
  6. 2:44 — Mini oven instead of a shaker: pause, cut, powder by hand
  7. 3:22 — Why: a 1.5 ft shaker tunnel cures too fast; conveyor ovens cure slowly
  8. 4:11 — Baking sheets in mini ovens: the highest quality cure
  9. 4:42 — L1800: 40 to 50 sheets a day; dual head: a roll or more, with an operator and UPS
  10. 5:10 — What DTF prints on: tees, leather, rexine, umbrellas; the right hot-melt per substrate
  11. 5:50 — Distributor and service in Tiruppur
  12. 6:23 — The traditional L1800 printer, fully loaded

Two printers, two volumes

If you have 100 or 200 sheets of production a day, the 12-inch XP600 dual head is the machine: fast, low maintenance compared to a 24-inch, and a head that costs far less than an i3200. Feeding options vary by model; that is a phone conversation, not a video. If you are at 40 or 50 sheets a day, the L1800-based printer does it and costs a fraction.

Comparison card: L1800-based DTF printer versus 12-inch XP600 dual head from the Tiruppur expo video
Pick by sheets per day.
Print Innovation Tiruppur stall with the 12-inch XP600 dual head printer, shaker and printed tees, caption free on-site training across India
The stall: dual head with shaker, L1800 beside it.
12-inch XP600 dual head DTF printer printing a white-ink roll at the expo
The dual head printing a roll.

The L1800, fully loaded

Forward-reverse module built in. The PE simulator so the sheet sensor is bypassed, no tape. Ink circulation, an external plastic unit, which is why the white density on its prints is as good as it is. It does about a roll to a roll and a half a day. People have run these for two or three years and are happy.

L1800-based DTF printer on the stall with film roll, caption we offer free on-site training and installation even for mini printers
The L1800 with roll, PE simulator and circulation fitted.
Converted L1800 DTF printer on the stall table with its external ink circulation unit
Fully loaded: forward-reverse, PE module, circulation.

Oven, not shaker

This is the opinion that surprises people. The shaker on a 12-inch has a curing tunnel about a foot and a half long; the film passes through fast. Screen printers use conveyor ovens for a reason: curing should be slow. So we print, pause, cut the sheet, powder by hand, and bake in a mini oven. Highest quality cure I know. If you want the shaker, we supply it with the machine; I just do not prefer it.

Operator placing a printed DTF sheet into a mini oven at the expo stall
Powdered sheet going into the mini oven.

Operator, UPS, substrates

The dual head needs a person on it all day and a UPS or inverter. The L1800 needs neither to the same degree. Both print the same things: t-shirts, and with the right hot-melt for each substrate, leather, rexine and even umbrellas, with no scratching or cracking. We have a distributor and service in Tiruppur.

Stall table with DTF printed t-shirts, leather and rexine samples and the dual head printer behind
Tees, leather and rexine samples on the stall.

Today

The L1800 is discontinued; its place is the converted L18050. The 12-inch dual head is the Yinstar 12-inch, and the oven is here. The same decision with 2024 numbers: L18050 vs 12-inch dual head.

Frequently asked questions

L1800 or 12-inch dual head?

40 to 50 sheets a day: L1800 class. 100 to 200 sheets: 12-inch XP600 dual head.

Why XP600 dual head rather than 24-inch?

Lower maintenance and a much cheaper head, for the same daily volumes most shops have.

Why do you cure in an oven instead of the shaker?

The shaker tunnel is short and fast; curing should be slow. We powder by hand and bake sheets in a mini oven.

What can DTF print on?

Cotton, polyester, leather, rexine, umbrellas, with the right hot-melt for each.

Is training included?

Yes, free on-site training and installation, even for the small printers.

Related guides

Which one for your volume?

WhatsApp your sheets per day and your city. Tiruppur has a distributor; the rest of India gets on-site installation.

WhatsApp +91 86555 56060

More videos: Dedicated DTF printers (X-ARC, Yinstar)