The 16 × 24 Double-Bed Automatic Heat Press, 100 Percent Made in India: Die-Cast Aluminium, Replaceable Coil, Auto Mode, Emergency Stop

Published 1 September 2024

Heat presses are where Indian shops lose money quietly: a Chinese coil burns, the whole plate has to be replaced, and the press sits idle for a month. This one is built here, and I walked around it at the expo in August 2024: double bed, die-cast aluminium, a coil you can change yourself, auto mode that presses when you slide the bed across, and an emergency stop. Four minutes, and the reason we started making our own.

Expo walkthrough, 4 min 23 s. August 2024. · Watch on YouTube

What the video shows

  1. 0:02 — 16 × 24 double bed: press one tee while loading the next
  2. 0:39 — Die-cast aluminium base and plates; bearings; grease points
  3. 1:16 — Auto and manual modes; the sensor presses when the bed slides left
  4. 1:45 — Work without a timer; lift mid-press
  5. 1:56 — The coil you can replace yourself
  6. 2:18 — Alpha temperature controller: one-year warranty; coil six months
  7. 2:36 — The 8 mm channel: it must never bend under pressure
  8. 2:58 — Compressor: minimum 1 HP, 50 litres
  9. 3:08 — Emergency stop
  10. 3:29 — Customisation and rebranding for B2B
  11. 3:49 — Sizes: 16 × 24, 24 × 36, 30 × 40; dealers in Mumbai, Kolkata, Bangalore, Pune

Double bed, auto mode

Two beds slide under one heated plate. Load a tee on the right while the left is pressing, slide, press. In auto mode a sensor at the end of the slide triggers the press by itself; manual mode waits for the button. The newer model lets you lift mid-press and work without a timer when you want to.

Spec card: Indian-made 16 x 24 double bed automatic heat press
Made in India, made to be repaired.
Operator standing beside the blue 16 x 24 double-bed automatic heat press at the expo
The double-bed press on the expo floor.
Close-up of the heated plate and pneumatic cylinder of the automatic heat press
The plate and cylinder.

Built to be repaired

Base and plates are die-cast aluminium, the bed runs on bearings with grease points you can reach. The heating coil can be replaced by you; on a Chinese press a dead coil means replacing the whole plate at a cost that makes people buy a new press. The temperature controller is an Alpha unit with a one-year warranty, and the coil carries six months.

Operator sliding the lower bed of the heat press to show the auto-mode sensor
Slide the bed; the sensor presses.
Control panel of the heat press with temperature controller, green start button and red emergency stop
Alpha controller, start, and the emergency stop.

How to judge any press

Watch the channel when the plate comes down. The frame must not bend, at all; this one has an 8 mm heavy channel and you will see no wear anywhere. A press that flexes gives uneven pressure and peeling edges. You need a compressor: 1 HP, 50 litres minimum. The emergency stop cuts the press instantly; open the switch and start again to resume.

Operator showing the rear frame and channel of the automatic heat press
The 8 mm channel at the back: it does not bend.
Operator pressing on the lower bed of the heat press to show rigidity
Pressing on the bed: no flex.

Sizes, B2B, demos

16 × 24, 24 × 36 and 30 × 40. B2B buyers can have features added or the press painted and rebranded in their colours. Live demos in Mumbai, with dealers in Kolkata, Bangalore and Pune. The press is here, the manual heavy-duty version here, and the pressing routine that goes with it is the right way to heat press.

Operator gesturing beside the automatic heat press at the expo stall
On the expo floor; demos in Mumbai.

Frequently asked questions

Why a double-bed heat press?

One bed presses while you load the other. Output nearly doubles for one operator.

Can I replace the coil myself?

Yes. That is the point of the design; imported presses need the whole plate replaced.

What compressor does it need?

Minimum 1 HP, 50 litres.

What is the warranty?

One year on the temperature controller, six months on the coil.

Can you rebrand it for my company?

Yes, for B2B buyers: custom features and paint.

Related guides

Need a press that can be repaired?

WhatsApp the size you need and your city; demos in Mumbai, dealers in Kolkata, Bangalore and Pune.

WhatsApp +91 86555 56060

More videos: DTF printing service and costs